PCB Etching: Difference between revisions
No edit summary |
|||
| (2 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
== Ätz-Station update 2019 == | |||
[[File:AetzStation3000.jpg|400px]] | |||
We just reinstalled some pumps, tubes and wires. | |||
=== Measuring Temperature === | |||
Also we installed the [https://hackteria.org/wiki/G%C3%A4r_L%C3%A4mpli Gär-Lämpli] to measure the temperature | |||
The temperature is display on the LED-ring starting at 25°C on the upper left and then in a circle to 55°C on the upper right. Also color changes according to temperature. if its yellow-orange optimal temperature is reached 45-50°C. | |||
New code can be uploaded through Audio, TinyAudioBoot, 8Bit Mixtape style. See the source here: | |||
https://github.com/GenericLab/Unagi_Gar-Lampli | |||
[[File:AetzLaempli.jpg|400px]] | |||
== Step by Step Photolithography == | == Step by Step Photolithography == | ||
| Line 55: | Line 72: | ||
[[File:PCB_waste_acetone.jpg|320px]] | [[File:PCB_waste_acetone.jpg|320px]] | ||
Ätze und Entwickler ins Hagenholz bringen. Die SGMK hat ein Kundenkonto. | |||
== Downloads == | == Downloads == | ||
[[File:ÄtzenHowTo.pdf]] | [[File:ÄtzenHowTo.pdf]] | ||
Latest revision as of 19:27, 15 December 2019
Ätz-Station update 2019
We just reinstalled some pumps, tubes and wires.
Measuring Temperature
Also we installed the Gär-Lämpli to measure the temperature
The temperature is display on the LED-ring starting at 25°C on the upper left and then in a circle to 55°C on the upper right. Also color changes according to temperature. if its yellow-orange optimal temperature is reached 45-50°C.
New code can be uploaded through Audio, TinyAudioBoot, 8Bit Mixtape style. See the source here:
https://github.com/GenericLab/Unagi_Gar-Lampli
Step by Step Photolithography
see external instructions: wetpong
can someone copy all the images to this wiki?
Preparation
-
Es wird eine NaOH Lösung vorbereitet, um anschliessend die belichteten Kupferplatten zu entwickeln
-
Reines Natriumhydroxid wird in ein Becherglas eingewogen, oder die abgepackten säckli verwenden
-
10g NaOH in 1L Wasser auflösen. Immer erst das Wasser dann die Lauge!
-
Rühren...
-
Heisses Wasser (ca. 35°C) in die Schale geben
-
Natronlauge im Behälter in die Schale mit warmem Wasser legen
-
Auf ca 35°C aufwärmen lassen
-
Temperatur mit Thermometer überwachen
Mask alignment and illumination
-
Folie auf das UV-Belichtungsgerät platzieren
-
Kupferplatte auf die Folie legen
-
Gerät schliessen, Zeit eingeben (ca. 2min)
-
Start
Development
-
Nun folgt der Prozess der Entwicklung. Nach dem Belichten, die Kupferplatte in das NaOH-Bad legen
-
Ca. 3 bis 5min wirken lassen und gelegentlich schwenken
-
Die Teile der Kupferplatte, welche belichtet wurden, werden durch das NaOH aufgelöst (Polymere brechen auf)
-
Kupferplatte aus dem Bad nehmen und mit Wasser abwaschen
Etching
-
Nun wird in einem Natrium Perfsulfat geätzt (ca. 400g Natriumpersulfat auf 1.5L Wasser)
-
Die Lösung wird auf ca. 50°C geheizt und mittels Thermometer überwacht
-
Die Kupferplatte wird zum Ätzen in das Peroxidbad gegeben und für 5min darin gelassen
-
Die Kupferplatte wird aus dem Bad genommen
Stripping / Final cleaning with acetone
-
Die Kupferplatte wird mit Wasser gespült
-
Eventuell noch mit Aceton nachwaschen, um den Fotolack zu entfernen
-
Um Aceton zu sparen am besten in einer wanne spülen, danach noch mit wasser abspülen
Waste disposal and Recycling
Ätze und Entwickler ins Hagenholz bringen. Die SGMK hat ein Kundenkonto.