Difference between revisions of "Ender3 v2"

From SGMK-SSAM-WIKI
Jump to: navigation, search
(Created page with "We got a new printer!!")
 
Line 1: Line 1:
 
We got a new printer!!
 
We got a new printer!!
 +
 +
 +
[[File:Ender3_MechArtLab.jpg|thumb|400px]]
 +
== Slice yourself using CURA ==
 +
 +
* install Cura 4.0.xx (newsest version)
 +
* Add "New Printer" and choose Ender3 (in older version just choose any rectangular and edit the print size)
 +
* Start with the pre-made settings or use dusjagr's "optimized" curaprofiles for draft (0.2mm) or fine (0.1mm)
 +
 +
[[:File:Ender3-CuraProfiles.zip]]
 +
 +
[[File:MachineSettings_Ender3.png|600px]]
 +
 +
== Print from microSD card ==
 +
 +
That's kinda the easiest and sofar gave me the best results.
 +
 +
== Connect via OctoPrint ==
 +
 +
Installed on OctoPrint. try this: http://octopi.local/ or: http://192.168.1.38/
 +
 +
Login with: mechartlab / MECHARTLAB WIFI KEY (check on whiteboard).
 +
 +
Choose Port:
 +
* '''/dev/ttyUSB0 for Ender3'''
 +
* /dev/ttyACM0 for [[MicroDelta]] aka RandeDelta
 +
 +
Choose Profile:
 +
* '''Neue Ender Siech im MechArtLab'''
 +
* RandeDelta
 +
 +
'''Connect'''
 +
 +
=== upload gcode ===
 +
 +
* Upload your gcode
 +
* Start to Print!!!
 +
 +
'''To Do:'''
 +
 +
* Upload to SD card notworking
 +
* Multiple printers on OctoPi
 +
* add LEDs!!
 +
 +
=== Slice on OctoPrint (experimental) ===
 +
 +
used this instruction: https://www.youtube.com/watch?v=0I_BIR36Grk
 +
 +
it's kinda working with the cura settings. but print quality not so good still....
 +
 +
[[File:Ender3_OctoPrintSlicing.jpg|640px]]

Revision as of 17:44, 24 July 2021

We got a new printer!!


Ender3 MechArtLab.jpg

Slice yourself using CURA

  • install Cura 4.0.xx (newsest version)
  • Add "New Printer" and choose Ender3 (in older version just choose any rectangular and edit the print size)
  • Start with the pre-made settings or use dusjagr's "optimized" curaprofiles for draft (0.2mm) or fine (0.1mm)

File:Ender3-CuraProfiles.zip

MachineSettings Ender3.png

Print from microSD card

That's kinda the easiest and sofar gave me the best results.

Connect via OctoPrint

Installed on OctoPrint. try this: http://octopi.local/ or: http://192.168.1.38/

Login with: mechartlab / MECHARTLAB WIFI KEY (check on whiteboard).

Choose Port:

  • /dev/ttyUSB0 for Ender3
  • /dev/ttyACM0 for MicroDelta aka RandeDelta

Choose Profile:

  • Neue Ender Siech im MechArtLab
  • RandeDelta

Connect

upload gcode

  • Upload your gcode
  • Start to Print!!!

To Do:

  • Upload to SD card notworking
  • Multiple printers on OctoPi
  • add LEDs!!

Slice on OctoPrint (experimental)

used this instruction: https://www.youtube.com/watch?v=0I_BIR36Grk

it's kinda working with the cura settings. but print quality not so good still....

Ender3 OctoPrintSlicing.jpg